Non-Motorized

Points of Inspection

Inspection Points for Non-Motorized RVs (Travel Trailers, 5th Wheels, Truck Campers)

This report will consist of 80 to 100 photos describing the items identified during the detailed Towable RV Inspection.

The Non-Motorized RV Inspection can include a fluid analysis of all oil and coolant fluids, including the tow vehicle. Fluid analysis samples of engine oil, transmission oil, engine coolant, generator oil, and hydraulic oil can be pre-purchased and performed during the inspection.

Roof

  • Inspect and rate the overall Roof Condition.

  • Identify the Roof material type and the sealants applied to the roof.

  • Evaluate the condition of the various sealant and joints around the roofing components.

  • Rate the condition of the roof vents, air conditioners, antenna, and other components mounted on the roof.

  • Identify areas of concern and potential water intrusion points.


Sidewall and End Caps

  • Inspect and identify the material type of the front and rear caps.

  • Evaluate the aging and general overall condition of the front and rear caps.

  • Inspect and evaluate the appearance and functional condition of the sidewalls, entrance doors, windows, and cargo access doors.

  • Inspect and evaluate any damage, discoloration, and delamination of the side wall and end cap components.


Slideout Rooms

  • Identify the types of slideout room drive systems.

  • Identify the type of roof material for the slideout room.

  • Inspect and rate the roof condition.

  • Inspect and evaluate the condition of the seals, sweeps, and gaskets for possible damage.

  • Evaluate the attached wiring and utility harness that feed underneath the slideout room.


Awnings and Slideout Toppers

  • Inspect and identify the operational type (manual or electric) of the awnings, slideout toppers, and window awnings.

  • Operate and rate the condition of the awning frames and latching mechanisms.

  • Evaluate and rate the condition of the fabric material of the awnings.


Chassis Turn Signal and Running Lights (12-volt DC) 

  • Inspect the condition of the 7-pin connector cord.

  • Operate and evaluate the emergency breakaway switch.

  • Activate and evaluate the operation of the DOT lights mounted on the RV.


120 Volt AC Electrical System (house type power)

  • Inspect and rate the condition of the power cord, and its connection ends.

  • Identify any damage or repair of the power cord.

  • Remove the cover panel of the 120-volt circuit breaker box to visually inspect the condition of the wiring, circuit breakers, and grounding connections.

  • List any heat discoloration to the wiring and connections.

  • Verify the separation of all the wiring types.

  • Test and verify the output operation of the 120 VAC to 12 VDC converter to charge the deep cycle batteries.


Generator - Engine - if installed, strongly recommend performing oil analysis to determine internal combustion engine component condition.

  • Identify and note the generators model, serial number, and run hours.

  • Check the oil level.

  • Start, operate and test the onboard generator under load.

  • Test the voltage output and frequency (60 cycles).


Inverter - if installed

  • Identify and note the model and the serial number of the inverter.

  • Visually inspect the wiring and electrical connections and fuses/circuit breakers.

  • Place an electrical load on the inverter to verify proper operation.

  • Test the voltage and frequency output of the inverter under fifty percent load.


Coach Battery System - (12-volt DC deep cycle Battery Electrical System)

  • Locate and note the location of the battery stack.

  • Evaluate the condition, age, and matched sizing of the battery stack.

  • Evaluate and determine if positive and negative cables are matched for a balanced load.

  • Access and visually inspect the wiring, fuse panel, and fuses of the 12-volt DC electrical system.

  • Evaluate the operation of the fresh water and waste water monitor panel for incorrect tank readings.

 

Fresh Water System

  • Verify the fresh water connections for the City Water hookup are operational.

  • Verify the onboard fresh water tank and pressure pump system will operate and maintain pressure.

  • Operationally test all fresh water fixtures inside and outside of the RV.

  • Visually inspect the water filtration system (if installed) for leaks and filter placement.


Waste Water Systems – (Gray and Black Water)

  • Operationally test and inspect waste (gray and black) plumbing systems for leaks under the sinks, shower, toilet, and discharge lines.

  • Identify the type of drain valve controls.

  • Verify the drain valves for both systems will maintain water in their tanks.

  • Operate both drain valves and test for ease of operation.

  • Verify the drain cap is in place and will hold waste water.


Life Safety Items

  • Perform and document LP gas timed leak test at cooktop burner spud for 5 minutes at 8 inches of water column gas pressure.

  • Test the Ground Fault Circuit Interrupter (GFCI) circuits in the 6-foot range of the water areas of the bathroom, kitchen, and exterior receptacles.

  • Test all wall receptacles for correct polarity and ground fault.

  • Test the exterior skin for Hot Skin that would cause electrical shock.

  • Emergency Exit Windows - Verify all safety windows are operational.

  • Fire Extinguisher - Verify unit is secure in the bracket, and the dial indicates the extinguisher is fully charged.

  • Smoke/Fire Detector - Test and verify the operation of the units.

  • Carbon Monoxide Detector (if applicable) - Test and verify the operation of the unit.

  • LP Gas Detector - Verify gas detection and audio alarm. Document the expiration date of the detector.

  • Verify the rubber grommet is sealed correctly around the LP gas line of the water heater.

 

LP Gas System

  • Visually inspect all hoses and pressure regulators for damage and age deterioration.

  • Verify plastic cover has been installed over the regulator.

  • On the Split tank system, verify the red-colored single-stage regulator is installed.


DOT Cylinders - if equipped

  • Document the manufacture dates of DOT cylinders.

  • List the location(s) of the DOT cylinders.

  • List the tank sizes that have been installed.

  • Conduct a visual inspection of the exterior of the cylinder for rust and other damage.


ASME tank - if equipped

  • Inspect the tank for rust or physical damage if the tank is visible.

  • List the location of the tank.

  • Document the manufacture date of the ASME tank if accessible.

  • List the gallon capacity of the tank.


Refrigerator

  • Identify the brand, model, and type of refrigerator.

  • Note the location of the vent panels used by the refrigerator.

  • Operate on all heat sources - 120-volt AC, LP gas, and 3-way refrigerators for 12-volt DC operation.

  • Collect the serial and model number and verify with the manufacturer if a recall notice has been issued and completed for this unit.

  • Visually verify if the baffle system on the back of the refrigerator area is correct and directing heat away from gas coils.

  • Test for the interior temperature of upper and lower refrigerator compartments and ice maker (if installed) if the refrigerator has been operating for a minimum of 12 hours.

  • Check the condition of the door frame, shelving, crisper drawers, door shelves, and interior light.

  • Evaluate and rate the freezer and refrigerator door gasket seals.


Water Heater

  • Identify the brand, model, and type of water heater.

  • Visually inspect burner assembly and gas exhaust system for blockages and insect infestation.

  • With water in the tank, verify operation on all heat sources - LP gas and 120-volt AC if equipped with a heating element.

  • If installed and visible, verify the positioning of bypass valves on the back of the water heater.

  • Determine if a proper drain plug is installed in the water heater tank.

  • If installed, inspect and evaluate if the correct type of dauber screen is used.


Furnace

  • If accessible, identify the brand, model, and type of furnace(s) that have been installed.

  • Identify the type of thermostat controls used to operate the furnace(s).

  • Visually inspect air intake and exhaust assemblies for blockages and insect infestation.

  • Operate and verify warm air discharge out of vents and proper return airflow to the unit.

  • Monitor for unusual noise or vibration of the blower motor.

  • If installed, inspect and evaluate if the correct type of dauber screen is used.


Cook Top / Stove

  • Evaluate and rate the condition of the cooktop or stove.

  • List the presence and condition of the stove top covers.

  • Verify the ignition and operation of all top burners and the oven flame (if equipped).

  • Inspect and rate the condition of the metal grill top and rubber grommets of the cooktop burner area.

  • Evaluate the presence of the units control knobs, door handles, and oven racks.


Air Conditioner(s)

  • Identify and list the type of cooling unit/heat pump.

  • Perform a cooling efficiency test (Delta T) on each unit.

  • Inspect the air filter(s) debris and cleanliness.


Washer / Dryer

  • Visually inspect and verify a wash and rinse cycle of the washer and dryer.

  • Visually inspect for leaks or damaged hoses.

  • Evaluate and rate the exterior condition of the dryer exhaust vent.


Microwave / Convection Oven

  • Identify and list the brand, model, type, and output wattage of the unit.

  • Verify the rack and turn tables are installed.

  • Operate the unit for 60 seconds utilizing a cup of water and then list the water temperature.


Dishwasher - if installed 

  • Identify and list the brand, model, and type of unit.

  • Verify the operation of the unit and inspect for leaks and non-functioning rotating racks and wash bars.


In-House Vacuum System - if installed 

  • Identify and list the brand, model, and type of unit.

  • Verify the operation and visually inspect the components of the hose assembly, access doors, and dirt bag.


Electric Fireplace - if installed 

  • Identify and list the brand, model, and type of unit.

  • Operate and verify the various heat settings, fan speed levels, and backlighting.


Cook Top Exhaust Fan

  • Operate and verify the condition of the exhaust function and fan speeds.

  • Visually inspect the filter and lighting.

  • Evaluate and rate the exterior condition of the exhaust vent.


Ceiling Mounted Fans and Ceiling Exhaust Vents

  • Visually inspect the condition of the blades and motor.

  • Operate and verify the condition of the blade direction and fan speeds.

  • Verify lighting if equipped.


Interior Conditions and Appearance

  • Visually inspect all ceilings, walls, interior doors, and flooring for signs of water intrusion, surface damage, or staining.

  • Operate all windows and doors, noting any deficiencies or missing components.

  • Evaluate the window coverings.

  • Operate all interior, exterior, and decor lighting, 12-volts and 120-volts.


Cabinets and Closet Condition

  • Inspect and evaluate all cabinet doors, drawers, and pull-out operations.

  • Visually inspect all countertops and flat surface areas of the kitchen, living room, bathroom, bedroom, and storage areas for scratches and damage.

  • Identify and list all broken and loose cabinet and closet hardware.

  • Note if the appearance of previous damage repairs has been performed.


Furniture

  • Visually inspect the condition of the dinette table/booth, chairs, recliners, and sofa.

  • Inspect and note furniture fabric tears, discoloration, and signs of excessive wear.

  • Visually inspect and note signs of mattress damage or staining.


Entertainment System

  • Visually inspect and operate all TV and stereo equipment.

  • Verify DVD/disc players and radios are operational.

  • Verify local channels, antenna, and 12-volt DC power signal booster are operational.

  • Raise, and lower roof mounted antenna if equipped.

  • Verify remotes are functional.


Shower/Tub Enclosure 

  • Visually inspect the glass panels, curtains, and soap dish areas.

  • Evaluate and rate the seals around the framework and doors for water leaks.

  • Operate the door and latch system to verify its operation.

  • Inspect and evaluate the stains and chemical/mineral buildup.


Running Gear

  • Type and number of axles.

  • Inspect the frame, axles, springs, rims, and other components for rust, oil stains, and visible damage.

  • Document the information on the tires as to their age and weight capacities.

  • Check tire pressure.

  • Inspect and rate tire tread condition.

  • Note any valve extensions and pressure monitors.


Hitch System/Hook Up

  • Inspect and identify the type of system used to tow the vehicle.

  • Evaluate and list modifications to the hitch system.


Leveling System

  • Identify and note the brand and type of system.

  • Operate by extending and retracting leveling system.

  • Check for hydraulic leaks or mechanical issues.


Weight Labels and Data Plates

  • Identify and document the Vehicle Identification Number (VIN).

  • Document the License plate info.

  • List the Inspection sticker information – if applicable.

  • List the RVIA inspection seal number.

  • List the Gross Vehicle Weight Rating.

  • List the date of manufacture.

  • List the Manufacturer’s Build Sheet (if available).

  • List Owner Stated Comments (if present).